Enum Ordering

#[non_exhaustive]
pub enum Ordering {
    Relaxed,
    Release,
    Acquire,
    AcqRel,
    SeqCst,
}

Atomic memory orderings

Memory orderings specify the way atomic operations synchronize memory. In its weakest Ordering::Relaxed, only the memory directly touched by the operation is synchronized. On the other hand, a store-load pair of Ordering::SeqCst operations synchronize other memory while additionally preserving a total order of such operations across all threads.

Rust’s memory orderings are the same as those of C++20.

For more information see the nomicon.

Variants (Non-exhaustive)

Non-exhaustive enums could have additional variants added in future. Therefore, when matching against variants of non-exhaustive enums, an extra wildcard arm must be added to account for any future variants.

Relaxed

No ordering constraints, only atomic operations.

Corresponds to memory_order_relaxed in C++20.

Release

When coupled with a store, all previous operations become ordered before any load of this value with Acquire (or stronger) ordering. In particular, all previous writes become visible to all threads that perform an Acquire (or stronger) load of this value.

Notice that using this ordering for an operation that combines loads and stores leads to a Relaxed load operation!

This ordering is only applicable for operations that can perform a store.

Corresponds to memory_order_release in C++20.

Acquire

When coupled with a load, if the loaded value was written by a store operation with Release (or stronger) ordering, then all subsequent operations become ordered after that store. In particular, all subsequent loads will see data written before the store.

Notice that using this ordering for an operation that combines loads and stores leads to a Relaxed store operation!

This ordering is only applicable for operations that can perform a load.

Corresponds to memory_order_acquire in C++20.

AcqRel

Has the effects of both Acquire and Release together: For loads it uses Acquire ordering. For stores it uses the Release ordering.

Notice that in the case of compare_and_swap, it is possible that the operation ends up not performing any store and hence it has just Acquire ordering. However, AcqRel will never perform Relaxed accesses.

This ordering is only applicable for operations that combine both loads and stores.

Corresponds to memory_order_acq_rel in C++20.

SeqCst

Like Acquire/Release/AcqRel (for load, store, and load-with-store operations, respectively) with the additional guarantee that all threads see all sequentially consistent operations in the same order.

Corresponds to memory_order_seq_cst in C++20.

Trait Implementations

impl Clone for Ordering

fn clone(&self) -> Ordering

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Ordering

fn fmt(&self, f: &mut Formatter<'_>) -> Result<(), Error>

Formats the value using the given formatter.

impl Hash for Ordering

fn hash<__H>(&self, state: &mut __H)

where __H: Hasher,

Feeds this value into the given Hasher.

fn hash_slice<H>(data: &[Self], state: &mut H)

where H: Hasher, Self: Sized,

Feeds a slice of this type into the given Hasher.

impl PartialEq for Ordering

fn eq(&self, other: &Ordering) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Ordering

impl Eq for Ordering

impl StructuralPartialEq for Ordering

Layout

Note: Most layout information is completely unstable and may even differ between compilations. The only exception is types with certain repr(...) attributes. Please see the Rust Reference's “Type Layout” chapter for details on type layout guarantees.

Size: 1 byte

Size for each variant:

• Relaxed: 0 bytes
• Release: 0 bytes
• Acquire: 0 bytes
• AcqRel: 0 bytes
• SeqCst: 0 bytes